 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| CML Microcircuits COMMUNICATION SEMICONDUCTORS UM6491/1 April 2004 DE6491 CMX649 Wireless Voice Link Demonstration Kit User Manual Advance Information Features * Full-Duplex Wireless Voice-Link Communication Demonstration using the CMX649 ADM Voice Codec Operates in the 863 - 865 MHz European Licence Free Band 20m Range - Line of Sight * * * * Privacy via CMX649 Digital Scrambler On/Off, Volume and RF Channel Pushbutton Controls Phone Quality Voice Transmission using Time Division Duplex (TDD) Airlink Protocol Selectable RF Power * * 1. Brief Description The DE6491 is a CMX649-based wireless voice link demonstration kit that demonstrates CMX649 ADM Codec IC operation in a low-power, cordless headset application. Operating as a short range RF device in the 863 - 865 MHz European licence-exempt band, this demonstration kit consists of two separate stand-alone PCBs each with the following sections: CMX649-based audio, RF transceiver and control. The basic design may be user adapted to other RF frequencies. Full-duplex voice operation at up to 20 metres range is provided via a single RF channel Time Division Duplex (TDD) link. With the supplied headsets a user can investigate two-way voice-audio transfer between units. Each PCB can be powered, standalone, from a choice of AAA batteries or a bench power supply. Intelligent power saving reduces supply current when not communicating. Each terminal draws between 17 - 25.5 mA when communicating or 850A, typical, when powersaved. Each on-board Controller's FLASH memory comes programmed with the latest version of operating firmware. If desired, a user may reprogram and in-circuit debug the Controller themselves, using a proprietary programmer (not included). 2004 CML Microsystems Plc DE6491 - CMX649 Wireless Voice Link DE6491 CONTENTS Section 1 2. Page Brief Description ................................................................................. 1 Preliminary Information ...................................................................... 4 2.1 Laboratory Equipment............................................................ 4 2.2 Handling Precautions ............................................................. 4 2.3 Approvals ................................................................................ 4 Quick Start ........................................................................................... 5 3.1 Setting-Up ............................................................................... 5 3.2 Operation................................................................................. 5 Signal Lists.......................................................................................... 8 Circuit Schematics and Board Layout ............................................. 10 Detailed Description.......................................................................... 11 6.1 Hardware Description ........................................................... 11 6.2 Firmware Description ........................................................... 12 6.3 Troubleshooting ................................................................... 15 Performance Specification................................................................ 16 7.1 Electrical Performance ......................................................... 16 3. 4. 5. 6. 7. It is always recommended that you check for the latest product datasheet version from the Datasheets page of the CML website: [www.cmlmicro.com]. 2004 CML Microsystems Plc 2 UM6491/1 DE6491 - CMX649 Wireless Voice Link DE6491 Figure 1 Interactive Block Diagram 2004 CML Microsystems Plc 3 UM6491/1 DE6491 - CMX649 Wireless Voice Link DE6491 2. 2.1 Preliminary Information Laboratory Equipment The following laboratory equipment is needed to use each evaluation board: * Two Alkaline AAA batteries or a 2.9 - 5.5 V power supply. 2.2 Handling Precautions Like most evaluation kits, this product is designed for use in laboratory environments. The following practices will help ensure its proper operation: 2.2.1 Static Protection This product uses low power CMOS circuits which can be damaged by electrostatic discharge. Partially damaged circuits can function erroneously, leading to misleading results. Observe ESD precautions at all times when handling this product. 2.2.2 Contents - Unpacking Please ensure that you have received all of the items on the separate information sheet (EK6491) and notify CML within 7 working days if the delivery is incomplete. 2.3 Approvals Each board contains a low-power radio frequency transceiver operating with FSK modulation in the 863 - 865 MHz band and is not approved by any regulatory agency or body. The boards are intended for experimental use only and the user is responsible for ensuring that the operation of these boards is both appropriate and lawful. 2004 CML Microsystems Plc 4 UM6491/1 DE6491 - CMX649 Wireless Voice Link DE6491 3. Quick Start This section provides instructions for users who wish to experiment immediately with the demonstration kit. A fuller description of the kit and its use appears later in this document. 3.1 Setting-Up Communication between the Master and Slave boards (see silk screen label for board type identification) can be established after the following steps are performed: 1. Connect the provided headsets to the sockets J3 and J3a on each board, ensuring the correct polarity of J3a. 2. Select the power supply for each board, either: * * Install 2 Alkaline AAA batteries (not supplied) in J1 and connect JP1 pin 1 to pin 2. Connect a 2.9 - 5.5 V power supply to J2 and connect JP1 pin 2 to pin 3. 3. Pair the boards - With the boards within RF range of each other (see section 3.2.5), perform the pairing sequence described in section 3.2.1. The boards will now be operational and the pairing process will not need to be performed again as the pairing information is retained in the microcontroller's non-volatile memory. 3.2 Operation Once a Master and Slave board (see silk screen label for board type identification) have been paired, they will be operational and audio communication can be achieved between them. Audio input to the Master board from the microphone will be heard in the Slave board's earpiece and audio from the Slave board's microphone will be heard in the Master board's earpiece. The four buttons provided on each board allow the user to turn the power on/off, reset the boards, control the volume, control RF channel selection and the pairing of two boards, as described below. 3.2.1 Pairing Boards Before the Master board and Slave board can communicate with one another, they must first be "paired". To perform the pairing process: Power the master and slave boards and place in close proximity Press and release the reset button (RST) on each board. Press and hold down the VOL- and VOL+ buttons on either the Slave or Master board. After 3 - 4 flashes of the LED, the LED will remain constantly on. While still holding the first pair of buttons, press and hold down the VOL- and VOL+ buttons on the other board. 6. After 3 - 4 flashes of the LED on the second board, the LED on the first board will go out. This indicates the new pairing ID codes have been successfully exchanged, the buttons on both boards can now be released. 7. The new pairing ID codes will be saved into non-volatile memory the next time the boards enter powersave mode. Once the two boards have been paired audio communication will be possible between them. The pairing process will only need to be performed once. Only if one of the paired boards is to be used with a different board should pairing need to be performed again. 1. 2. 3. 4. 5. 2004 CML Microsystems Plc 5 UM6491/1 DE6491 - CMX649 Wireless Voice Link DE6491 3.2.2 Power Functions The LED (D1) present on each board indicates the power state of the board as: * * * * When the board leaves powersave mode and is powered up, the LED will stay on for approximately 0.5s. The LED will flash periodically, once every second, when a board is powered. The LED will flash twice in quick succession when the board is entering powersave mode. When in powersave mode the LED will be inactive. Both automatic and manual powersave functions are provided. 3.2.2.1 Automatic Power Functions The automatic power functions allow the boards to power up and powersave when appropriate without any user interaction. If voice is absent on both boards for a period greater than approximately 30 seconds, the boards will enter powersave mode. The Master board and the Slave board, if paired, will wake from powersave mode if voice is present at the audio input to the Master board, i.e. from its microphone. Also, the Slave board will automatically powersave if an RF connection to a paired Master board is lost for an extended period (approximately 300ms), i.e. if the Slave board is moved out of range or the Master board ceases communicating abruptly. Once an RF connection can again be established with an active paired Master board, the Slave board will wake from powersave mode. 3.2.2.2 Manual Power Functions Both boards provide controls to manually power up or powersave. By simultaneously pressing both the VOL- button and VOL+ button on a board, the power state of the board will be toggled. If a Master board is manually powersaved or powered up, a paired Slave board will also be powersaved or powered up, if it is in range. Manually changing the power state of the Slave board will not effect a paired Master board. NB - Due to the automatic power functions, described in section 3.2.2.1, a board manually powersaved or powered up may not remain power saved or powered up. 3.2.3 Adjusting Volume Levels Two buttons are provided for earpiece volume controls, VOL+ and VOL-, which increase or decrease the volume, respectively. Simply press and release either the VOL+ button or the VOLbutton to adjust the volume. Holding the button down will not ramp the volume. There are 32 volume increments available using the DE6491 board's volume control buttons. The volume level selected is retained when the boards are powersaved. The selected volume level will only be lost if the power supply is removed or if the board is reset. 2004 CML Microsystems Plc 6 UM6491/1 DE6491 - CMX649 Wireless Voice Link DE6491 3.2.4 RF Channel Selection The Channel button (CHNL) on each board allows the RF channel used for communication to be changed; which may be required if RF interference is disrupting communications. To change the RF channel simply press and release the channel button (CHNL) on one of the boards. Both boards will then attempt to communicate on a different RF channel. If the interference is too great and the RF channel cannot be changed successfully, communication may be lost. To force both boards to use the same default RF channel again, both boards must be reset, as described in section 3.2.6. 3.2.5 RF Power Selection Four settings are available to allow the RF power output of each board to be adjusted. The setting is selected by inserting or removing shorting links between pins 5 and 6 and pins 7 and 8 on header J4. RF_POW0 and RF_POW1 (J4 pins 5 and 6) Link Open Link Open RF_POW2 and RF_POW3 (J4 pins 7 and 8) Link Link Open Open RF Power setting Maximum (default) High Low Minimum Approx. RF Power (dBm) +5.0 -2.0 -8.0 -19.0 Typical Current Draw (mA) 25.5 20 18 17 Maximum RF range* (metres) 20.0 12.0 8.0 3.0 *These range figures are for when the embedded PCB antenna is used and both paired boards use the same RF power setting. The achievable RF range may vary depending on the environmental conditions, including a building's structure and any obstacles between the boards. 3.2.6 Reset Function To reset a board press and release the RST button. Resetting a board will set both the volume level and RF channel to their default values. Communication may be lost between two paired boards if only one is reset. To recover communications simply reset the other board to ensure both boards are communicating using the default RF channel. 2004 CML Microsystems Plc 7 UM6491/1 DE6491 - CMX649 Wireless Voice Link DE6491 4. Signal Lists CONNECTOR PINOUT Connector Ref. J2 J3 Connector Pin No. 1 2 B C D Signal Name VSS VIN VSS SPKR-OUT MIC-IN1 MIC-IN2 SPARE1 SPARE2 SPARE3 SPARE4 RF_POW0 RF_POW1 RF_POW2 RF_POW3 VDD VSS TDO TDI VDD TMS TCK VSS RST - Signal Type Power Power Power O/P I/P I/P BI BI BI BI O/P I/P O/P I/P Power Power O/P I/P Power I/P I/P Power I/P - Description External Power Supply Connection External Power Supply Connection VSS Connection Analogue Voice Output to Headset Earpiece No Connection Analogue Voice Input from Headset Microphone Analogue Voice Input from Headset Microphone Spare MSP430 I/O Spare MSP430 I/O Spare MSP430 I/O Spare MSP430 I/O RF Transmit Power Selection Pin RF Transmit Power Selection Pin RF Transmit Power Selection Pin RF Transmit Power Selection Pin (See section 3.2.5 for details) VDD Connection VSS Connection MSP430 JTAG Output No Connection MSP430 JTAG Input MSP430 JTAG Reference Voltage Output MSP430 JTAG Input No Connection MSP430 JTAG Input No Connection VSS Connection No Connection MSP430 JTAG Input No Connection J3a 1 2 J4 1 2 3 4 5 6 7 8 9 10 J5 1 2 3 4 5 6 7 8 9 10 11 12,13,14 2004 CML Microsystems Plc 8 UM6491/1 DE6491 - CMX649 Wireless Voice Link DE6491 CONNECTOR PINOUT Connector Ref. J6 Connector Pin No. N/A Signal Name ANT_EXT Signal Type Antenna Description External Antenna Connection (See section 6.1.3 for details) TEST POINTS Test Point Ref. TP1 TP2 TP3 TP4 TP5 TP6 TP7 TP8 TP9 Default Measurement 2.9V-5.5V 0V N/A N/A N/A 2.7V N/A N/A 0V Unregulated VDD VSS TEST0 TEST1 TEST2 2.7V_RF - CC1000 Power Supply CC1000 DIO Signal CC1000 DCLK Signal VSS Description JUMPERS Link Ref. JP1 Positions 1 - 2: J1 - AAA Battery Holder 2 - 3: J2 - External Power Supply Default Position 1-2 Description Power Supply Source - Selects which power supply to use Notes: I/P = O/P = BI = Input Output Bi-directional 2004 CML Microsystems Plc 9 UM6491/1 DE6491 - CMX649 Wireless Voice Link DE6491 5. Circuit Schematics and Board Layout For clarity, circuit schematics are available as separate high resolution files. Figure 2 Demonstration Board Layout 2004 CML Microsystems Plc 10 UM6491/1 DE6491 - CMX649 Wireless Voice Link DE6491 6. 6.1 Detailed Description Hardware Description Both boards consist of three main ICs: the CML Microcircuits CMX649, as the voice codec, the Chipcon CC1000, for the RF communication, and the Texas Instruments MSP430F147 microcontroller to control and transfer the data between the other two ICs and support the user interface and airlink protocol. 6.1.1 Voice Codec Circuitry The voice codec circuitry consists of the CMX649 and external passive components recommended by the CMX649 datasheet. The microphone amplifier has low and high -3dB frequency roll-off points of approximately 150Hz and 15kHz, respectively. To reduce the codec circuitry's footprint and cost, the CMX649 clock signal is provided by the MSP430F147 and not by a crystal oscillator. A Maxim MAX4368 audio amplifier is used to drive the earpiece with the Audio Out signal from the CMX649. Its external components are designed for a highpass roll-off frequency of approximately 150Hz when used with the 32 impedance headset speaker. 6.1.2 RF Transceiver Circuitry The RF transceiver circuitry is based on the Chipcon CC1000PP reference design and the passive components have been chosen to provide operation in the European wireless audio band of 863 - 865 MHz, as stated in the CEPT ERC recommendation 70-03 Annex 13. Changes in passive component values, firmware adjustments and the use of an external antenna would allow a different RF band to be used for communication, see Chipcon documentation for details. 6.1.3 RF Antenna Two options are provided for the RF antenna: an embedded antenna printed on each PCB (default) and an external antenna which can be connected via the SMA connector J6. The embedded antenna is selected when R6 is a shorting link and R7 is not fitted, the external antenna is selected when R6 is not fitted and R7 is a shorting link. 6.1.4 Headsets Connectors J3 and J3a allow the supplied headsets, each consisting of a microphone and earpiece, to be attached to the boards. 6.1.5 Expansion Connector J4 is provided for user expansion. Four unused I/O lines of the MSP430F147 and VDD and VSS are available at this header. 6.1.6 In-Circuit Programming Connector J5 provides connections to the MSP430F147 microcontroller's JTAG interface to allow the device to be reprogrammed and debugged using the proprietary programmer, Texas Instruments MSP430 Flash Emulation Tool MSP-FETP430IF (not provided). The following instructions are a guide to program and debug the MSP430F147 firmware: 2004 CML Microsystems Plc 11 UM6491/1 DE6491 - CMX649 Wireless Voice Link DE6491 1. Connect the MSP-FET430IF to J5 2. Connect a power supply or battery 3. Start the programming or debug sequence in accordance with the programming tool manufacturer's specifications. 6.2 Firmware Description A Texas Instruments MSP430F147IPM microcontroller is fitted to each of the DE6491 boards and has been programmed by CML, before shipment, with the latest version of firmware. Please read the separate information sheet (EK6491) and check the CML website for firmware status. The latest source code and programming files (EF6491xxM.d43 and EF6491xxS.d43, for the Master firmware and Slave firmware, respectively, `xx' represents the version number) can be downloaded from the CML website. There are two types of firmware included with the DE6491 demonstration kit, one for the Master board and one for the Slave board (see silk screen label for board type identification), both have the same basic structure, as shown in Figure 3. The firmware controls the CML Microcircuits CMX649 Voice Code, the Chipcon CC1000 RF transceiver and handles the transfer of data between them. All communication is synchronised by the Master board. 6.2.1 The MSP430F147's Interaction with the CMX649 On both the Master board and the Slave board, the CMX649 and its data are handled in the same way. The CMX649 is set to use 31.25kbps ADM to encode and decode the audio, which is created by dividing down a 4MHz clock signal provided by the MSP430F147. The CMX649 is sent control commands from the MSP430F147 via the CBUS serial interface, see the CMX649 datasheet for details on the CBUS. The MSP430F147 buffers data received from the CMX649 into packets, each one containing approximately 30ms of audio, to be exchanged over the RF link. The Master board's firmware also takes advantage of the CMX649's programmable voice activity detector (VAD) to determine when voice/audio is present. This allows the Master board to decide when to powersave, i.e. after periods where voice/audio is consistently absent, and to wake from powersave, i.e. when voice/audio has been detected. 6.2.2 The MSP430F147's Interaction with the CC1000 The CC1000 and its data are handled by the MSP430F147 in an almost identical manner on both the Master board and the Slave board. Control signals are sent to the CC1000 by the MSP430F147 via the CC1000's 3-wire serial interface. Data is transferred over the RF link by the CC1000 at 76.8kbps and, therefore, data is transferred between the CC1000 and the MSP430F147 at the same rate. The audio packets collected from the CMX649 are converted into RF frames by the MSP430F147 and transmitted over the RF link by the CC1000. Data is transferred over the RF link as half-duplex but provides the user with full-duplex audio communication because the CC1000's data rate is over twice the CMX649's data rate; i.e. two RF frames can be exchanged serially over the RF link, one in each direction, within the time it takes the CMX649 to encode one audio packet and decode another audio packet in parallel. 2004 CML Microsystems Plc 12 UM6491/1 DE6491 - CMX649 Wireless Voice Link DE6491 Reset or power supply reconnected Periodic Wake-up from powersave mode Initialise MSP430 Restore RF Channel and Volume Level Defaults Initialise MSP430 Should communication be established with another unit? No Yes Initialise CMX649 and CC1000 Begin Communications No Return to powersave mode? Yes Go to powersave mode Wait for Wake-up from powersave mode Figure 3 MSP430F147 Firmware Program Flow 6.2.3 Firmware Structure 2004 CML Microsystems Plc 13 UM6491/1 DE6491 - CMX649 Wireless Voice Link DE6491 The firmware is event driven with time-critical functions being performed in interrupt routines. There are four events that can cause an interrupt to be signalled: * * * * The CMX649 is ready to transfer digital audio, one byte that has been encoded by the CMX649, received by the MSP430F147, and one byte transmitted by the MSP430F147, to be decoded by the CMX649. (Handled by firmware function "CMX649_TRANSFER"). The CC1000 has received a byte from the RF link when in receive mode. (Handled by firmware function "RFCHIPRX"). The CC1000 is ready to transmit a byte over the RF link when in transmit mode. (Handled by the firmware function "RFCHIPTX"). The VOL-, VOL+ or CHNL button has been pressed. (Handled by the firmware functions "BUTTON_DEBOUNCE" and "BUTTONS"). As well as performing their own functions, the interrupt handlers can set flags to request that the board: * * * * Switches to RF receive mode or RF transmit mode. Toggles the power state. Changes the volume level Exchanges a new RF channel to communicate on. When a board is powered and communicating, the firmware function "MAINLOOP" continuously executes so that when a flag is set "MAINLOOP" can call the appropriate subroutine to perform the requested function, see Figure 4. These functions are performed by "MAINLOOP" as they are less time critical than those performed by the interrupt handlers. 6.2.4 CMX649 Register Configuration The firmware configures the CMX649 registers as follows: Register Name AAF/AIF BANDWIDTH AUDIO INPUT LEVEL CTRL POWER CONTROL 1 POWER CONTROL 2 CODEC MODE CONTROL SCRAMBLER CONTROL CLK DIVIDER CONTROL CLK SOURCE CONTROL CODEC INTERUPT CONTROL DECODER MODE AND SETUP DECODER ADM CONTROL DECODE VAD THRESHOLD DECODE OFF-SET LEVEL ENCODER MODE AND SETUP ENCODER ADM CONTROL ENCODE VAD THRESHOLD ENCODE OFF-SET LEVEL Register Address (hex) 61 63 64 65 70 71 72 73 81 D0 D1 D2 D3 E0 E1 E2 E3 Register Value (hex) 00 C0 55 55 00 9xxx (where `xxx' is a random number E340 30F8 88 01B8 4999 0400 0004 01B8 499A 0400 0004 2004 CML Microsystems Plc 14 UM6491/1 DE6491 - CMX649 Wireless Voice Link DE6491 6.3 Troubleshooting Communication may be lost between two paired boards after a reset or reconnection of the power supply to one of the boards. Both of these events will cause the RF channel that board uses for communication to be reset to the default channel. Performing a reset on the other board will force both boards to use the same default RF channel and communication can be re-established. Figure 4 MAINLOOP Flow 2004 CML Microsystems Plc 15 UM6491/1 DE6491 - CMX649 Wireless Voice Link DE6491 7. 7.1 Performance Specification Electrical Performance 7.1.1 Absolute Maximum Ratings Exceeding these maximum ratings can result in damage to the Demonstration Kit. Min. -0.3 -0.3 0 -2 Max. 6 3.0 +30 +2 Units V V mA mA Supply (VIN - VSS) Voltage on any connector pin to VSS Current into or out of VIN and VSS pins Current into or out of any other connector pin 7.1.2 Operating Limits Correct operation of the Demonstration Kit outside these limits is not implied. Notes Supply (VIN - VSS) Operating Temperature Operating Frequency (RF) Min. 2.9 +10 863 Max. 5.5 +35 865 Units V C MHz 7.1.3 Operating Characteristics VIN - VSS = 3.0V, Tamb = +25C. Notes DC Parameters IDD (powersave, Master) IDD (powersave, Slave) IDD (periodic wake from powersave, Master) IDD (periodic wake from powersave, Slave) IDD (powered and communicating, RF Range setting = Minimum) IDD (powered and communicating, RF Range setting = Low) IDD (powered and communicating, RF Range setting = High) IDD (powered and communicating, RF Range setting = Maximum) RF Range with: RF Power Setting = Minimum RF Power Setting = Low RF Power Setting = High RF Power Setting = Maximum Min. - - - - - - - - Typ. 500 420 2.1 13.0 17.0 18.0 20.0 25.5 Max. - - - - - - - - Units A A mA mA mA mA mA mA - - - - - - - - 3.0 8.0 12.0 20.0 m m m m 2004 CML Microsystems Plc 16 UM6491/1 DE6491 - CMX649 Wireless Voice Link DE6491 CML does not assume any responsibility for the use of any circuitry described. No IPR or circuit patent licences are implied. CML reserves the right at any time without notice to change the said circuitry and any part of this product specification. Evaluation kits and demonstration boards are supplied for the sole purpose of demonstrating the operation of CML products and are supplied without warranty. They are intended for use in a laboratory environment only and are not for re-sale, end-use or incorporation into other equipments. Operation of these kits and boards outside a laboratory environment is not permitted within the European Community. All software/firmware is supplied "as is" and is without warranty. It forms part of the product supplied and is licensed for use only with this product, for the purpose of demonstrating the operation of CML products. Whilst all reasonable efforts are made to ensure that software/firmware contained in this product is virus free, CML accepts no resonsibility whatsoever for any contamination which results from using this product and the onus for checking that the software/firmware is virus free is placed on the purchaser of this evaluation kit or development board. www.cmlmicro.com For FAQs see: www.cmlmicro.com/products/faqs/ For a full data sheet listing see: www.cmlmicro.com/products/datasheets/download.htm For detailed application notes: www.cmlmicro.com/products/applications/ CML Microcircuits (UK) Ltd CML Microcircuits (USA) Inc. 4800 Bethania Station Road, Winston-Salem, NC 27105 - USA. CML Microcircuits (Singapore)Pte Ltd COMMUNICATION SEMICONDUCTORS Oval Park, Langford, Maldon, Essex, CM9 6WG - England. No 2 Kallang Pudding Road, #09 to 05/06 Mactech Industrial Building, Singapore 349307 No. 218, Tian Mu Road West, Tower 1, Unit 1008, Shanghai Kerry Everbright City, Zhabei, Shanghai 200070, China. Tel: +86 21 6317 4107 +86 21 6317 8916 Fax: +86 21 6317 0243 Sales: cn.sales@cmlmicro.com.cn Technical Support: sg.techsupport@cmlmicro.com Tel: +44 (0)1621 875500 Fax: +44 (0)1621 875600 Sales: sales@cmlmicro.com Technical Support: techsupport@cmlmicro.com Tel: +1 336 744 5050, 800 638 5577 Fax: +1 336 744 5054 Sales: us.sales@cmlmicro.com Technical Support: us.techsupport@cmlmicro.com Tel: +65 6745 0426 Fax: +65 6745 2917 Sales: sg.sales@cmlmicro.com Technical Support: sg.techsupport@cmlmicro.com |
Price & Availability of DE6491
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |